International (refereed) journals

1.

“Coupled-PDMS grafted mesoporous γ-alumia membranes for solvent nanofiltration”, Cheryl R. Tanardi, Arian Nijmeijer and Louis Winnubst, Separation and Purification Technology, 169 (2016) 223-229

2.

“Polyethyleneglycol grafting of γ-alumina membranes for solvent resistant nanofiltration”, Cheryl R. Tanardi, Romina Catana, Mihai Barboiu, André Ayral, Ivo F.J. Vankelecom, Arian Nijmeijer and Louis Winnubst, Microporous and Mesoporous Materials, 229 (2016) 106-116

3.

“Preparation of alumina membranes comprising a thin separation layer and a support with straight open pores for water desalination”, Jianqiang Gu, Chunlei Ren, Xu Zong, Chusheng Chen and Louis Winnubst, Ceramics International, 42 (2016) 12427-12434

4.

“Chemical modification/grafting of mesoporous alumina with polydimethylsiloxane (PDMS)”, Ana F.M. Pinheiro, Arian Nijmeijer, Venkata G.P. Sripathi and Louis Winnubst, European Journal of Chemistry, 6 (2015) 287-295

5.

“Solvent permeation behavior of PDMS grafted γ-alumina membranes”, Cheryl R. Tanardi, Ivo F.J. Vankelecom, Ana F.M. Pinheiro, Kishore K.R. Tetala, Arian Nijmeijer and Louis Winnubst, Journal of Membrane Science, 495 (2015) 216-225

6.

“Membrane-integrated oxy-fuel combustion of coal: Process design and simulation”, Wei Chen, Louis van der Ham, Arian Nijmeijer and Louis Winnubst, Journal of Membrane Science, 492 (2015) 461-470

7.

“Auto-combustion synthesis of perovskite-type oxides SrTi1−xFexO3−δ”, S.F.P. ten Donkelaar, R. Ruhl, S.A. Veldhuis, A. Nijmeijer, L. Winnubst, H.J.M. Bouwmeester, Ceramics International, 41 (2015) 13709-13715

8.

“Facile synthesis of zirconia doped hybrid organic inorganic silica membranes”, Marcel ten Hove, Arian Nijmeijer and Louis Winnubst, Separation and Purification Technology, 147 (2015) 372-378

9.

“An accurate way to determine the ionic conductivity of mixed ionic–electronic conducting (MIEC) ceramics”, Wei Chen, Nicolas Nauels, Henny J.M. Bouwmeester, Arian Nijmeijer and Louis Winnubst, Journal of the European Ceramic Society 35 (2015) [11] 3075-3083

10.

“Hybrid silica membranes with enhanced hydrogen and CO2 separation properties”, Hessel L. Castricum, Hammad F. Qureshi, Arian Nijmeijer and Louis Winnubst, Journal of Membrane Science, 488 (2015) 121-128

11.

“Doped microporous hybrid silica membranes for gas separation”, Hammad F. Qureshi, Rogier Besselink, Johan E. ten Elshof, Arian Nijmeijer and Louis Winnubst, Journal of Sol-Gel Science and Technology, 75 (2015) [1] 180-188

12.

“A novel malonamide bridged silsesquioxane precursor for enhanced dispersion of transition metal ions in hybrid silica membranes”, Rogier Besselink, Hammad F. Qureshi, Louis Winnubst and Johan E. ten Elshof, Micro and Mesoporous Materials, 214 (2015) 45-53

13.

“Preparation and characterization of hydrophobic alumina planar membranes for water desalination”, Chunlei Ren, Hong Fang, Jianqiang Gu, Louis Winnubst and Chusheng Chen, Journal of the European Ceramic Society, 35 (2015) 723-730

14.

“Waste-to-resource preparation of a porous ceramic membrane support featuring elongated mullite whiskers with enhanced porosity and permeance”, Li Zhu, Yingchao Dong, Stuart Hampshire, Sophie Cerneaux and Louis Winnubst, Journal of the European Ceramic Society, 35 (2015) 711-721

15.

“Modeling water flux and salt rejection of mesoporous γ-alumina and microporous organosilica membranes”, Ali Farsi, Vittorio Boffa, Hammad F. Qureshi, Arian Nijmeijer, Louis Winnubst and Morten Lykkegaard Christensen, Journal of Membrane Science, 470 (2014) 307-315

16.

“PDMS grafting of mesoporous γ-alumina membranes for nanofiltration of organic solvents”, Cheryl R. Tanardi, Ana F.M. Pinheiro, Arian Nijmeijer and Louis Winnubst, Journal of Membrane Science, 469 (2014) 471-477

17.

“Oxygen-selective membranes integrated with oxy-fuel combustion”, Wei Chen, Chu-sheng Chen, Henny Bouwmeester, Arian Nijmeijer and Louis Winnubst, Journal of Membrane Science, 463 (2014) 166-172

18.

“Development of a PDMS-grafted alumina membrane and its evaluation as solvent resistant nanofiltration membrane”, Ana F.M. Pinheiro, Danny Hoogendoorn, Arian Nijmeijer and Louis Winnubst, Journal of Membrane Science, 463 (2014) 24-32

19.

“Phase-inversion tape casting and oxygen permeation properties of supported ceramic membranes”, Wei He, Hua Huang, Jian-fen Gao, Louis Winnubst and Chu-sheng Chen, Journal of Membrane Science, 452 (2014) 294-299

20.

“Preparation and electrical properties of Ni0.6Mn2.4-xSnxO4 NTC ceramics”, Zhongbing Wang, Zhenbo Li, Yi Zhang, Ruyian Zhang, Pan Qin, Chunnian Chen and Louis Winnubst, Ceramics International, 40 (2014) 4875-4878

21.

“Influence of sol–gel process parameters on the microstructure and performance of hybrid silica membranes”, Hammad F. Qureshi, Arian Nijmeijer and Louis Winnubst, Journal of Membrane Science, 446 (2013) 19-25

22.

“Phase-inversion tape casting and synchrotron-radiation computed tomography analysis of porous alumina”, Hong Fang, Chunlei Ren, Yaoge Liu, Detang Lu, Louis Winnubst and Chu-sheng Chen, Journal of the European Ceramic Society, 33 (2013) 2049-205

23.

“Open source powder based rapid prototyping machine for ceramics”, A. Budding, T.H.J. Vaneker and L. Winnubst, Procedia, 6 (2013) 533-538

24.

“Oxygen non-stoichiometry determination of perovskite materials by a carbonation process”, Wei Chen, Arian Nijmeijer and Louis Winnubst, Solid State Ionics, 229 (2012) 54-58

25.

“Applying ceramic nanoporous microneedle arrays as a transport interface in egg plants and an ex-vivo human skin model”, Michel Verhoeven, Svetlana Bystrova, Louis Winnubst, Hammad F. Qureshi, Tanja D. de Gruijl, Rik J. Scheper and Regina Luttge, Microelectronic Engineering 98 (2012) 659-662

26.

“Effect of temperature on friction and wear behaviour of CuO–zirconia composites”, Mahdiar Valefi, Matthijn de Rooij, Dirk J. Schipper and Louis Winnubst, Journal of the European Ceramic Society, 32 [12] (2012) 2235-2242

27.

“Towards a generic method for inorganic porous hollow fibers preparation with shrinkage-controlled small radial dimensions, applied to Al2O3, Ni, SiC, stainless steel, and YSZ”, Mieke W.J. Luiten-Olieman, Michiel J.T. Raaijmakers, Louis Winnubst, Ton C. Bor, Matthias Wessling, Arian Nijmeijer and Nieck E. Benes, Journal of Membrane Science, 407-408 (2012) 155-163

28.

“Production and characterization of micro- and nano-features in biomedical alumina and zirconia ceramics using a tape casting route”, Maciej Domanski, Louis Winnubst, Regina Luttge, Edwin Lamers, X. Frank Walboomers, John Jansen and Han Gardeniers, Journal of Materials Science: Materials in Medicine, 23 [7] (2012) 1637-1444

29.

“Processing and in vivo evaluation of multiphasic calcium phosphate cements with dual tricalcium phosphate phases”, Marco A. Lopez-Heredia, Matilde Bongio, Marc Bohner, Vincent Cuijpers, Louis Winnubst, Natasja van Dijk, Joop G.C. Wolke, Jeroen J.J.P. van den Beucken and John A. Jansen, Acta Biomaterialia, 8 (2012) 3500-3508

30.

“Non-glycosylated BMP-2 can induce ectopic bone formation at lower concentrations compared to glycosylated BMP-2”, F.C.J. van de Watering, J.J.J.P. van den Beucken, S.P. van der Woning, A. Briest, A. Eek, H. Qureshi, L. Winnubst, O.C. Boerman and J.A. Jansen, Journal of Controlled Release, 159 (2012) 69-77

31.

“In vitro and in vivo evaluation of the inflammatory response to nanoscale grooved substrates”, Edwin Lamers, X. Frank Walboomers, Maciej Domanski, Ljupcho Prodanov, Jacoline Melis, Regina Luttge, Louis Winnubst, James M. Anderson, Han J.G.E. Gardeniers, and John A. Jansen, Nanomedicine: Nanotechnology, Biology and Medicine, 8 (2012) 308-317

32.

“The effect of an alumina counterface on friction reduction of CuO/3Y-TZP composite at room temperature”, Jiupeng Song, Mahdiar Valefi, Matthijn de Rooij, Dirk J. Schipper and Louis Winnubst, Wear, 274-275 (2012) 75-83

33.

“Submicron-patterning of bulk titanium by nanoimprint lithography and reactive ion etching”, M. Domanski, R. Luttge, E. Lamers, X.F. Walboomers, L. Winnubst, J.A. Jansen and J.G.E. Gardeniers, Nanotechnology 23 [6] (2012) 065306 (12pp)

34.

“High-temperature tribological and self-lubricating behavior of copper oxide-doped Y-TZP composite sliding against alumina”, Mahdiar Valefi, Matthijn de Rooij, Dirk J. Schipper and Louis Winnubst, Journal of the American Ceramic Society, 94 [12] (2011) 4426-4434

35.

“Ta-doped SrCo0.8 Fe0.2O3-δ membranes: Phase stability and oxygen permeation in CO2 atmosphere”, Wei Chen, Chusheng Chen and Louis Winnubst, Solid State Ionics, 196 [1] (2011) 30-33

36.

Porous stainless steel hollow fibers with shrinkage-controlled small radial dimensions”, Mieke W.J. Luiten-Olieman, Michiel J.T. Raaijmakers, Louis Winnubst, Matthias Wessling, Arian Nijmeijer and Nieck E. Benes, Scripta Materialia, 65 [1] (2011) 25-28

37.

Effect of microstructure and catalyst coating on the oxygen permeability of a novel CO2-resistant composite membrane”, Shumin Fang, Chusheng Chen and Louis Winnubst, Solid State Ionics, 190 (2011) 46-52

38.

“The effect of ball milling grinding pathways on the bulk and reactivity properties of calcium phosphate cements”, M. A. Lopez-Heredia, M. Bohner, W. Zhou, A. J. A. Winnubst, J. G. C. Wolke and J. A. Jansen, Journal of Biomedical Materials Research - Part B: Applied Biomaterials, 98B (2011) 68-79

39.

“Composite capillary membrane for solvent resistant nanofiltration”, S.M. Dutczak, M.W.J. Luiten-Olieman, H.J. Zwijnenberg, L.A.M. Bolhuis-Versteeg, L. Winnubst, M.A. Hempenius, N.E. Benes, M. Wessling and D. Stamatialis, Journal of Membrane Science, 372 [1-2] (2011) 182-190

40.

“Porous stainless steel hollow fiber membranes via dry-wet spinning”, Mieke W.J. Luiten-Olieman, Louis Winnubst, Arian Nijmeijer, Matthias Wessling and Nieck E. Benes, Journal of Membrane Science, 370 [1-2] (2011) 124-130

41.

“Manipulation of sintering behavior by initial freeze pressing an aqueous alumina suspension”, Jumeng Zheng, Louis Winnubst, Velianti, Shumin Fang and David Salamon, Advanced Engineering Materials, 13 [1-2] (2011) 77-81

42.

Effect of Zr4+ doping on the oxygen stoichiometry and phase stability of SrCo0.8Fe0.2O3−δ oxygen separation membrane”, W. Chen, Y.B. Zuo, C.S. Chen and A.J.A. Winnubst, Solid State Ionics, 181 (2010) 971-975

43.

“Ceramic microfluidic monoliths by ice templating”, Jumeng Zheng, David Salamon, Leon Lefferts, Matthias Wessling and Louis Winnubst, Microporous and Mesoporous Materials 134 (2010) 216-219

44.

“Synthesis and characteristics of 3Y-TZP and CuO powders for ceramic composites”, Louis Winnubst, Peter J. de Veen, Shen Ran and Dave H.A. Blank, Ceramics International, 36 (2010) 847-853

45.

“Effect of TiO2 doping on the characteristics of macroporous Al2O3/TiO2 membrane supports”, Hong Qi, Yiqun Fan, Weihong Xing and Louis Winnubst, Journal of the European Ceramic Society, 30 [6] (2010) 1317-1325

46.

Manipulating microstructure and mechanical properties of CuO doped 3Y-TZP nano-ceramics using spark-plasma sintering”, Shen Ran, Jozef Vleugels, Shuigen Huang, Kim Vanmeensel, Dave H.A. Blank and Louis Winnubst, Journal of the European Ceramic Society, 30 [4] (2010) 899-904

47.

“Cryo dualbeam focused ion beam-scanning electron microscopy to evaluate the interface between cells and nanopatterned scaffolds”, E. Lamers, X. F. Walboomers, M. Domanski, G. McKerr, B.M. O’Hagan, C.A. Barnes, L. Peto, R. Lüttge, L. Winnubst, H.G.J. Gardeniers and J. A. Jansen, Tissue Engineering-Part C: Methods 17 [1] (2010) 1-7

48.

“The influence of nanoscale grooved substrate on osteoblast behavior and extracellular matrix deposition”, Edwin Lamers, X. Frank Walboomers, Maciej Domanski, Joost te Riet, Falco van Delft, Regina Luttge, Louis Winnubst, Han Gardeniers and John A. Jansen, Biomaterials 31 (2010) 3307-3316

49.

“A novel method for the fabrication of freestanding PZT features on substrates”, Joost G. van Bennekom, Louis Winnubst, Wietze Nijdam, Matthias Wessling and Rob G.H. Lammertink, Journal of the European Ceramic Society, 29 [15] (2009) 3227-3233

50.

“Dry-sliding self-lubricating ceramics: CuO doped 3Y-TZP”, Shen Ran, Louis Winnubst, Dave H.A. Blank, Henry R. Pasaribu, Jan-Willem Sloetjes and Dik J. Schipper, Wear, ­267 (2009) 1696-1701

51.

Analysis of reactions during sintering of CuO-doped 3Y-TZP nano-powder composites”, Louis Winnubst, Shen Ran, Emiel A. Speets and Dave H.A. Blank, Journal of the European Ceramic Society, 29 [12] (2009) 2549-2557

52.

Aging of nickel manganite NTC ceramics”, Dao-lai Fang, Cui-hong Zeng, Chu-sheng Chen and A.J.A. Winnubst, Journal of Electroceramics, 22 (2009) 421-427

53.

“Effects of Cu and Zn co-doping on the electrical properties of Ni0.5Mn2.5O NTC ceramics”, Chunhua Zhao, Biyun Wang, Pinghua Yang, Louis Winnubst and Chusheng Chen, Journal of the European Ceramic Society, 28 [1] (2008) 35-40

54.

Preparation and electrical properties of FexCu0.10Ni0.66Mn2.24−xO4 (0 ≤ x ≤ 0.90) NTC ceramics” Dao-lai Fang, Chu-sheng Chen and A.J.A. Winnubst, Journal of Alloys and Compounds, 454 [1-2] (2008) 286-291

55.

“Effect of microstructure on the tribological and mechanical properties of CuO-doped 3Y-YZP ceramics”, Shen Ran, Louis Winnubst, Dave H. A. Blank, Henry R. Pasaribu, Jan-Willem Sloetjes and Dik J. Schipper, Journal of the American Ceramic Society, 90 [9] (2007) 2747-2752

56.

“Sintering behaviour and microstructure of 3Y-TZP + 8 mol% CuO nano-powder composite”, S. Ran, A.J.A. Winnubst, H. Koster, P. de Veen and D.H.A. Blank, Journal of the European Ceramic Society, 27 [2-3] (2007) 683-687

57.

Stability and oxygen permeation behavior of Ce0.8Sm0.2O2−δ–La0.8Sr0.2CrO3−δ composite membrane under large oxygen partial pressure gradients”, Bo Wang, Jianxin Yi, Louis Winnubst and Chusheng Chen, Journal of Membrane Science, 286 [1-2] (2006) 22-25

58.

“Effect of annealing in O2 or N2 on the aging of Fe0.5Mn1.84Ni0.66O4 NTC-ceramics”, Zhongbing Wang, Chunhua Zhao, Pinghua Yang, Louis Winnubst and Chusheng Chen, Solid State Ionics, 177 [19-25] (2006) 2191-2194

59.

“Oxygen permeation through a Ce0.8Sm0.2O2−δ–La0.8Sr0.2CrO3−δ dual-phase composite membrane”, Jianxin Yi, Yanbo Zuo, Wei Liu, Louis Winnubst and Chusheng Chen, Journal of Membrane Science, 280 [1-2] (2006) 849-855

60.

“X-ray diffraction and infrared studies of FexMn2.34-xNi0.66O4 (0<x<1) NTC ceramics”, Zhongbing Wang, Chunhua Zhao, Pinghua Yang, A.J.A. Winnubst, Chusheng Chen, Journal of the European Ceramic Society, 26 [13] (2006) 2833-2837

61.

“Synthesis, sintering and microstructure of 3Y-TZP/CuO nano-powder composites”, Shen Ran, Louis Winnubst, Wika Wiratha and Dave H.A. Blank, Journal of the European Ceramic Society, 26 [4-5] (2006) 391-396

62.

“Preparation of Ultra-Fine Nickel Manganite Powders and Ceramics by a Solid-State Coordination Reaction”, Dao-lai Fang, Zhong-bing Wang, Ping-hua Yang, Wei Liu, Chu-sheng Chen and A.J.A. Winnubst, Journal of the American Ceramic Society, 89 [1] (2006) 230-235

63.

“Sintering Behavior of 0.8 mol%-CuO-Doped 3Y-TZP Ceramics”, Shen Ran, Louis Winnubst, Wika Wiratha and Dave H.A. Blank, Journal of the American Ceramic Society, 89 [1] (2006) 151-155

64.

“Environmental effects on friction and wear of dry sliding zirconia and alumina ceramics doped with copper oxide”, H.R. Pasaribu, K.M. Reuver, D.J. Schipper, S. Ran. K.W. Wiratha, A.J.A. Winnubst and D.H.A. Blank, International Journal of Refractory Metals and Hard Materials, 23 (2005) 386 - 390

65.

“Research and education on inorganic and ceramic materials in the Netherlands”, H.T. Hintzen and A.J.A. Winnubst, J. Soc. Inorg. Mater. Japan, 12 (2005) 222-231

66.

“Friction and wear studies on nylon-6/SiO2 nanocomposites”, Monserrat Garcia, Matthijn de Rooij, Louis Winnubst, Werner E. van Zyl and H. Verweij, Journal of Applied Polymer Science, 92 [3] (2004) 1855 -186

67.

“Friction behaviour of solid oxide lubricants as second phase in a-Al2O3 and Stabilized ZrO2 composites” Bas Kerkwijk, Monserat Garcia, Werner E. van Zyl, Louis Winnubst, Elmer J. Mulder, Dik J. Schipper and Henk Verweij, Wear, 256 (2004) 182 -189

68.

“A wear-resistant zirconia ceramic for low friction application”, A.J.A. Winnubst, S. Ran, K.W. Wiratha, D.H.A. Blank, H.R. Pasaribu, J-W. Sloetjes and D.J. Schipper, Key Engineering Materials 264-268 (2004) 809-812

69.

“Densification of zirconia-hematite nanopowders”, T.P. Raming, A.J.A. Winnubst, W.E. van Zyl and H. Verweij, Journal of the European Ceramic Society, 23 [7] (2003) 1053-1060

70.

“Electrochemical characterisation of 3Y-TZP-Fe2O3 composites” B.A. Boukamp, T.P. Raming, A.J.A. Winnubst and H. Verweij, Solid State Ionics, 158 (2003) 381-394

71.

“The synthesis and characterisation of mixed Y2O3-doped ZrO2 and a-Fe2O3 nanosized powders” T.P. Raming, A.J.A. Winnubst and H. Verweij, Journal of Materials Chemistry, 12 (2002) 3705 – 3711

72.

“The synthesis and magnetic properties of nanosized hematite (a-Fe2O3) particles” T.P. Raming, A.J.A. Winnubst, C.M. van Kats and A.P. Philipse, Journal of Colloid and Interface Science, 249 (2002) 346-350

73.

“Synthesis and characterisation of dual-phase Y-TZP and RuO2 nanopowders: dense electrode precursors”, Werner E. van Zyl, Louis Winnubst, Tomas P. Raming, Riaan Schmuhl and Henk Verweij, Journal of Materials Chemistry, 12 [3] (2002) 708-713

74.

“Analysis of In-doped CaZrO3 using a peroxo-oxalate complexation method”, Leen van Rij, Louis Winnubst, Le Jun and Joop Schoonman, Journal of Materials Chemistry, 10 [11] (2000) 2515-2521

75.

“Processing of homogeneous zirconia-toughened alumina ceramics with high dry-sliding wear resistance”, Bas Kerkwijk, Louis Winnubst, Elmer J. Mulder and Henk Verweij, Journal of the American Ceramic Society, 82 [8] (1999) 2087-2093

76.

“Preparation of BaTiO3 by homogeneous precipitation” S. van der Gijp, M.H.J. Emond, A.J.A. Winnubst and H.Verweij, Journal of the European Ceramic Society, 19 (1999) 1683-1690

77.

“Peroxo-oxalate preparation of doped barium titanate”, Sven van der Gijp, Louis Winnubst and Henk Verweij, Journal of the American Ceramic Society, 82 [5] (1999) 1175-1180

78.

“Tribological properties of nanoscale alumina-zirconia composites” B. Kerkwijk, A.J.A. Winnubst, H. Verweij, W.J. Mulder, H.S.C. Metselaar, and D.J. Schipper, Wear, 225-229 (1999) 1293-1302

79.

“Thermally induced wear of ceramics” H.S.C. Metselaar, A.J.A. Winnubst and D.J. Schipper, Wear, 225-229 (1999) 857 – 861

80.

"Superplastic deep drawing of tetragonal zirconia ceramics at 1160°C", A.J.A. Winnubst and M.M.R. Boutz, Journal of the European Ceramic Society, 18 (1998) 2101-06

81.

“Preparation of La0.3Sr0.7CoO3-δ perovskite by thermal decomposition of metal-EDTA complexes", R.H.E. van Doorn, H. Kruidhof, A. Nijmeijer, A.J.A. Winnubst and A.J. Burggraaf, Journal of Materials Chemistry, 8 [9] (1998) 2109-12

82.

"An oxalate-peroxide complex used in the preparation of doped barium titanate", S. van der Gijp, A.J.A. Winnubst and H. Verweij, Journal of Materials Chemistry, 8 [5] (1998) 1251-54

83.

“Effects of grain size and ceria addition on ageing behaviour and tribological properties of Y-TZP ceramics”, S.R. Jansen, A.J.A. Winnubst, Y.J. He, H. Verweij P.G.T. van der Varst and G. de With, Journal of the European Ceramic Society, 18 (1998) 557 – 553

84.

“Effects of a second phase on the tribological properties of Al2O3 and ZrO2 ceramics”, Y.J.He, A.J.A. Winnubst, D.J. Schipper, A.J. Burggraaf and H. Verweij, Wear, 210 (1997) 178-187

85.

“Sliding wear of ZrO2 - Al2O3 composite ceramics”, Y.J. He, A.J.A. Winnubst, A.J. Burggraaf, H. Verweij, P.G.T. van der Varst and G. de With, Journal of the European Ceramic Society, 17 (1997) 1371-1380

86.

Influence of porosity on friction and wear of tetragonal zirconia polycrystals”, Yingjie He, Louis Winnubst, Antonie J. Burggraaf, Henk Verweij, Paul G.Th. van der Varst and Bert de With, Journal of the American Ceramic Society, 80 [2] (1997) 377-80

87.

“Grain growth in ultra-fine grained Y-TZP ceramics”, C.D. Sagel-Ransijn, A.J.A. Winnubst, A.J. Burggraaf and H. Verweij, Journal of the European Ceramic Society, 17 (1997) 1133-141

88.

“Production of defect-poor nanostructured ceramics of yttria-zirconia”, C.D. Sagel-Ransijn, A.J.A. Winnubst, B. Kerkwijk, A.J. Burggraaf and H. Verweij, Journal of the European Ceramic Society, 17 (1997) 831-841

89.

“Plasticity of nanocrystalline zirconia ceramics and composites”, A.J.A. Winnubst, M.M.R. Boutz, Y.J. He, A.J. Burggraaf and H. Verweij, Ceramics International, 23 (1997) 215-221

90.

“Zirconia-toughened alumina (ZTA) with improved homogeneity for tribological applications”, B. Kerkwijk, A.J.A. Winnubst, A.F. Stassen and H. Verweij, Key Engineering Materials, 132-136 (1997) 297-300

91.

“Wet chemical preparation of doped barium titanate powders and ceramics”, S. van der Gijp, A.J.A. Winnubst and H. Verweij, Key Engineering Materials, 132-136 (1997) 77-80

92.

“Grain-size dependence of sliding wear in tetragonal zirconia polycrystals”, Yingjie He, Louis Winnubst, Antonie J. Burggraaf, Henk Verweij, Paul G.Th. van der Varst and Bert de With, Journal of the American Ceramic Society, 79 (1996) 3090-3096

93.

"Enhanced mechanical properties by grain boundary strengthening in ultra-fine-grained TZP ceramics", Y.J. He, A.J.A. Winnubst, C.D. Sagel-Ransijn, A.J. Burggraaf and H. Verweij, Journal of the European Ceramic Society, 16 [6] (1996) 601-612

94.

”The influence of crystallisation and washing medium on the characteristics of nanocrystalline Y-TZP”, C.D. Sagel-Ransijn, A.J.A. Winnubst, H. Verweij and A.J. Burggraaf, Journal of the European Ceramic Society, 16 (1996) 759-766

95.

"The effect of ceria co-doping on chemical stability and fracture toughness of Y-TZP", M.M.R. Boutz, A.J.A. Winnubst, B. van Langerak, R.J.M. Olde Scholtenhuis, K. Kreuwel and A.J. Burggraaf, Journal of Materials Science, 30 (1995) 1854-1862

96.

"Friction and wear behaviour of ceramic-hardened steel couples under reciprocating sliding motion", Y.J. He, A.J.A. Winnubst, D.J. Schipper, P.M.V. Bakker, A.J. Burggraaf and H. Verweij, Wear, 184 (1995) 33-43

97.

"Microstructural development, electrical properties and oxygen permeation of zirconia-palladium composites", C.S. Chen, B.A. Boukamp, H.J.M. Bouwmeester, G.Z. Cao, H. Kruidhof, A.J.A. Winnubst and A.J. Burggraaf, Solid State Ionics, 76 [1-2] (1995) 23-28,

98.

"Low-temperature sinter forging of nanostructured Y-TZP and YCe-TZP", Michel M.R. Boutz, Louis Winnubst, Antonie J. Burggraaf, Marco Nauer and Claude Carry, Journal of the American Ceramic Society, 78 (1995) 121-128

99.

"Sinter forging of zirconia toughened alumina", Y.J. He, A.J.A. Winnubst, H. Verweij and A.J. Burggraaf, Journal of Materials Science, 29 (1994) 6505-6512

100.

"Improvement of mechanical properties of zirconia-toughened alumina by sinter forging", Y.J. He, A.J.A. Winnubst, H. Verweij and A.J. Burggraaf, Journal of Materials Science, 29 (1994) 5868-5874

101.

"Characterization of grain boundaries in superplastically deformed Y-TZP ceramics", Michel M.R. Boutz, Chusheng Chen, Louis Winnubst and Antonie J. Burggraaf, Journal of the American Ceramic Society, 77 (1994) 2632‑2640

102.

"Effect of additives on densification and deformation of tetragonal zirconia", M.M.R. Boutz, A.J.A. Winnubst, F. Hartgers and A.J. Burggraaf, Journal of Materials Science, 29 (1994) 5374-5382

103.

"Effect of calcination on the sintering of gel-derived zirconia-toughened alumina", Peter den Exter, Louis Winnubst, Theo H.P. Leuwerink and Antonie J. Burggraaf, Journal of the American Ceramic Society, 77 [9] (1994) 2376-2380

104.

"Low temperature superplastic flow of yttria stabilized tetragonal zirconia polycrystals", M.M.R. Boutz, A.J.A. Winnubst, A.J. Burggraaf, M. Nauer and C. Carry, Journal of the European Ceramic Society, 13 (1994) 103-111

105.

"Yttria-ceria stabilized tetragonal zirconia polycrystals: Sintering, grain growth and grain boundary segregation", M.M.R. Boutz, A.J.A. Winnubst and A.J. Burggraaf, Journal of the European Ceramic Society, 13 (1994) 89-102

106.

"A hydrothermal route for production of dense, nanostructured Y-TZP", M.M.R. Boutz, R.J.M. Olde Scholtenhuis, A.J.A. Winnubst and A.J. Burggraaf, Materials Research Bulletin, 29 (1994) 31-40

107.

"Thermal stability of nanostructured titania and titania-ceria ceramic powders prepared by the sol-gel process", G.W. Koebrugge, A.J.A. Winnubst and A.J. Burggraaf, Journal of Materials Chemistry, 3 (1993) 1095-1100

108.

"The electrical characterization of grain boundaries in ultra-fine grained Y-TZP", C.S. Chen, M.M.R. Boutz, B.A. Boukamp, A.J.A. Winnubst, K.J. de Vries and A.J. Burggraaf, Materials Science and Engineering A: Structural materials, 168 (1993) 231-234

109.

"The preparation and characterization of Y-TZP/20 wt.% alumina", P. den Exter, A.J.A. Winnubst and A.J. Burggraaf, Journal of the European Ceramic Society, 11 (1993) 497-507

110.

"Sintering kinetics and microstructure development of nanoscale Y-TZP ceramics", G.S.A.M. Theunissen, A.J.A. Winnubst and A.J. Burggraaf, Journal of the European Ceramic Society, 11 (1993) 315-324

111.

"Surface and grain boundary analysis of doped zirconia ceramics studied by AES and XPS", G.S.A.M. Theunissen, A.J.A. Winnubst and A.J. Burggraaf, Journal of Materials Science, 27 (1992) 5057

112.

"Mechanical properties of ultra-fine grained zirconia ceramics", G.S.A.M. Theunissen, J.S. Bouma, A.J.A. Winnubst and A.J. Burggraaf, Journal of Materials Science, 27 (1992) 4429

113.

"Effect of dopants on the sintering behaviour and stability of tetragonal zirconia ceramics", G.S.A.M. Theunissen, A.J.A. Winnubst and A.J. Burggraaf, Journal of the European Ceramic Society, 9 (1992) 251

114.

"The influence of MgO on the microstructure during sintering of fine-grained alumina and zirconia/alumina composite", A. Bos, P.J.M. Grefte, P. den Exter, A.J.A. Winnubst, E.B.M. Doesburg, A.J. Burggraaf and H.J. Veringa, Science of Sintering, 23 (1991) 19-24

115.

"Powder preparation and compaction behaviour of fine-grained Y-TZP", W.F.M. Groot Zevert, A.J.A. Winnubst, G.S.A.M. Theunissen and A.J. Burggraaf, Journal of Materials Science, 25 (1990) 3449

116.

"Segregation aspects in the ZrO2-Y2O3 system", G.S.A.M. Theunissen, A.J.A. Winnubst and A.J. Burggraaf, Journal of Materials Science Letters, 8 (1989) 55

117.

"Microstructure characteristics of ultra-fine ZrO2-Y2O3 ceramic powders", A.J.A. Winnubst, W.F.M. Groot Zevert, G.S.A.M. Theunissen and A.J. Burggraaf, Materials Science and Engineering, A109 (1989) 215

118.

“The analytical SEM and STEM, an indispensable tool in ceramics research”, B.A. Boukamp, A.J.A. Winnubst, K. Keizer, K.J. de Vries and A.J. Burggraaf, Ultramicroscopy 24­ [4] (1988) 426-427

119.

"Tetragonal ZrO2-Y2O3, Part I: Preparation methods and characterisation", A.J.A. Winnubst, M.A.C.G. van de Graaf, K. Keizer, and A.J. Burggraaf, J. Phys. Colloques, 47 (1986) C1.596

120.

"Tetragonal ZrO2-Y2O3: Part II: The mechanical and electrical properties", K. Keizer, M. van Hemert, A.J.A. Winnubst, M.A.C.G. van de Graaf and A.J. Burggraaf, J. Phys. Colloques, 47 (1986) C1.783

121.

"Response behaviour of oxygen sensing solid electrolytes", A.J.A. Winnubst, A.H.A. Scharenborg and A.J. Burggraaf, Journal of Applied Electrochemistry, 15 (1985) 139

122.

"The electrode resistance of ZrO2-Y2O3(-Bi2O3) solid electrolytes with Pt electrodes", A.J.A. Winnubst, A.H.A. Scharenborg and A.J. Burggraaf, Solid State Ionics, 14 (1984) 319

123.

"The luminescence of yttria stabilized zirconia doped with Bi2O3", G. Blasse, Hao Zhiran, A.J. A. Winnubst and A.J. Burggraaf, Materials Research Bulletin, 19 (1984) 1057

124.

"Preparation and electrical properties of a monophasic ZrO2-Y2O3-Bi2O3 solid electrolyte", A.J.A. Winnubst and A.J. Burggraaf, Materials Research Bulletin, 19 (1984) 613

125.

"AES/STEM grain boundary analysis of stabilized zirconia ceramics", A.J.A. Winnubst, P.J.M. Kroot and A.J. Burggraaf, Journal of Physics and Chemistry of Solids, 44 (1983) 955-960

126.

"Mechanical properties and fracture behaviour of ZrO2-Y2O3 ceramics", A.J.A. Winnubst, K. Keizer and A.J. Burggraaf, Journal of Materials Science, 18 (1983) 1958-1966

127.

"Effect of impurities on sintering and conductivity of yttria-stabilized zirconia", M.J. Verkerk, A.J.A. Winnubst and A.J. Burggraaf, Journal of Materials Science, 17 (1982) 3113-3122